Cu(In,Ga)(S,Se)2 solar cells and modules by electrodeposition

S. Taunier; J. Sicx-Kurdi; P. P. Grand; A. Chomont; O. Ramdani; L. Parissi; P. Panheleux; N. Naghavi; C. Hubert; M. Ben-Farah; J. P. Fauvarque; J. Connolly; O. Roussel; P. Mogensen; E. Mahé; J. F. Guillemoles; D. Lincot; O. Kerrec

doi:10.1016/j.tsf.2004.11.200

Cu(In,Ga)(S,Se)₂ solar cells and modules by electrodeposition

S. Taunier
, J. Sicx-Kurdi
, P. P. Grand
, A. Chomont
, O. Ramdani
, L. Parissi
, P. Panheleux
, N. Naghavi
, C. Hubert
, M. Ben-Farah
, J. P. Fauvarque
, J. Connolly
, O. Roussel
, P. Mogensen
, E. Mahé
, J. F. Guillemoles
, D. Lincot
, O. Kerrec

Lamsid/EDF/R and D
Saint-Gobain

Résultats de recherche: Contribution à un journal › Article › Revue par des pairs

Résumé

The CIS by electrodeposition (CISEL) project between Electricité de France (EDF), Centre National de la Recherche Scientifique (CNRS)/Ecole Nationale Supérieure de Chimie de Paris (ENSCP) and Saint-Gobain Recherche (SGR) aims at developing a low-cost electrodeposition process for Cu(In,Ga)(S,Se)₂ (CIGS) solar cells. The process is characterized by two main steps: (i) deposition of the precursor film and (ii) thermal annealing. This process enables the preparation of a large range of sulfur containing absorbers, with S/(S+Se) atomic ratio from 0% to more than 90%. The films are single phase over the whole composition range. The influence of Sulfur content on the microstructure has been shown with grain sizes decreasing with increasing sulfur content. Efficient solar cells can be obtained from all the different precursor compositions, with efficiencies of over 10% on lab cells on sulfur-rich absorbers, and 6-7% on 30×30 cm² devices. The homogeneity of 15×15 cm² substrates is also discussed.

langue originale	Anglais
Pages (de - à)	526-531
Nombre de pages	6
journal	Thin Solid Films
Volume	480-481
Les DOIs	https://doi.org/10.1016/j.tsf.2004.11.200
état	Publié - 1 juin 2005
Modification externe	Oui

Accès au document

10.1016/j.tsf.2004.11.200

Contient cette citation

Taunier, S., Sicx-Kurdi, J., Grand, P. P., Chomont, A., Ramdani, O., Parissi, L., Panheleux, P., Naghavi, N., Hubert, C., Ben-Farah, M., Fauvarque, J. P., Connolly, J., Roussel, O., Mogensen, P., Mahé, E., Guillemoles, J. F., Lincot, D., & Kerrec, O. (2005). Cu(In,Ga)(S,Se)₂ solar cells and modules by electrodeposition. Thin Solid Films, 480-481, 526-531. https://doi.org/10.1016/j.tsf.2004.11.200

@article{21332ab066e14f52a6e12ab733272bec,

title = "Cu(In,Ga)(S,Se)2 solar cells and modules by electrodeposition",

abstract = "The CIS by electrodeposition (CISEL) project between Electricit{\'e} de France (EDF), Centre National de la Recherche Scientifique (CNRS)/Ecole Nationale Sup{\'e}rieure de Chimie de Paris (ENSCP) and Saint-Gobain Recherche (SGR) aims at developing a low-cost electrodeposition process for Cu(In,Ga)(S,Se)2 (CIGS) solar cells. The process is characterized by two main steps: (i) deposition of the precursor film and (ii) thermal annealing. This process enables the preparation of a large range of sulfur containing absorbers, with S/(S+Se) atomic ratio from 0\% to more than 90\%. The films are single phase over the whole composition range. The influence of Sulfur content on the microstructure has been shown with grain sizes decreasing with increasing sulfur content. Efficient solar cells can be obtained from all the different precursor compositions, with efficiencies of over 10\% on lab cells on sulfur-rich absorbers, and 6-7\% on 30×30 cm2 devices. The homogeneity of 15×15 cm2 substrates is also discussed.",

keywords = "Cu(In,Ga)(S,Se) solar cells, Electrodeposition, Sulfur",

author = "S. Taunier and J. Sicx-Kurdi and Grand, \{P. P.\} and A. Chomont and O. Ramdani and L. Parissi and P. Panheleux and N. Naghavi and C. Hubert and M. Ben-Farah and Fauvarque, \{J. P.\} and J. Connolly and O. Roussel and P. Mogensen and E. Mah{\'e} and Guillemoles, \{J. F.\} and D. Lincot and O. Kerrec",

year = "2005",

month = jun,

day = "1",

doi = "10.1016/j.tsf.2004.11.200",

language = "English",

volume = "480-481",

pages = "526--531",

journal = "Thin Solid Films",

issn = "0040-6090",

}

Taunier, S, Sicx-Kurdi, J, Grand, PP, Chomont, A, Ramdani, O, Parissi, L, Panheleux, P, Naghavi, N, Hubert, C, Ben-Farah, M, Fauvarque, JP, Connolly, J, Roussel, O, Mogensen, P, Mahé, E, Guillemoles, JF, Lincot, D & Kerrec, O 2005, 'Cu(In,Ga)(S,Se)₂ solar cells and modules by electrodeposition', Thin Solid Films, VOL. 480-481, p. 526-531. https://doi.org/10.1016/j.tsf.2004.11.200

TY - JOUR

T1 - Cu(In,Ga)(S,Se)2 solar cells and modules by electrodeposition

AU - Taunier, S.

AU - Sicx-Kurdi, J.

AU - Grand, P. P.

AU - Chomont, A.

AU - Ramdani, O.

AU - Parissi, L.

AU - Panheleux, P.

AU - Naghavi, N.

AU - Hubert, C.

AU - Ben-Farah, M.

AU - Fauvarque, J. P.

AU - Connolly, J.

AU - Roussel, O.

AU - Mogensen, P.

AU - Mahé, E.

AU - Guillemoles, J. F.

AU - Lincot, D.

AU - Kerrec, O.

PY - 2005/6/1

Y1 - 2005/6/1

N2 - The CIS by electrodeposition (CISEL) project between Electricité de France (EDF), Centre National de la Recherche Scientifique (CNRS)/Ecole Nationale Supérieure de Chimie de Paris (ENSCP) and Saint-Gobain Recherche (SGR) aims at developing a low-cost electrodeposition process for Cu(In,Ga)(S,Se)2 (CIGS) solar cells. The process is characterized by two main steps: (i) deposition of the precursor film and (ii) thermal annealing. This process enables the preparation of a large range of sulfur containing absorbers, with S/(S+Se) atomic ratio from 0% to more than 90%. The films are single phase over the whole composition range. The influence of Sulfur content on the microstructure has been shown with grain sizes decreasing with increasing sulfur content. Efficient solar cells can be obtained from all the different precursor compositions, with efficiencies of over 10% on lab cells on sulfur-rich absorbers, and 6-7% on 30×30 cm2 devices. The homogeneity of 15×15 cm2 substrates is also discussed.

AB - The CIS by electrodeposition (CISEL) project between Electricité de France (EDF), Centre National de la Recherche Scientifique (CNRS)/Ecole Nationale Supérieure de Chimie de Paris (ENSCP) and Saint-Gobain Recherche (SGR) aims at developing a low-cost electrodeposition process for Cu(In,Ga)(S,Se)2 (CIGS) solar cells. The process is characterized by two main steps: (i) deposition of the precursor film and (ii) thermal annealing. This process enables the preparation of a large range of sulfur containing absorbers, with S/(S+Se) atomic ratio from 0% to more than 90%. The films are single phase over the whole composition range. The influence of Sulfur content on the microstructure has been shown with grain sizes decreasing with increasing sulfur content. Efficient solar cells can be obtained from all the different precursor compositions, with efficiencies of over 10% on lab cells on sulfur-rich absorbers, and 6-7% on 30×30 cm2 devices. The homogeneity of 15×15 cm2 substrates is also discussed.

KW - Cu(In,Ga)(S,Se) solar cells

KW - Electrodeposition

KW - Sulfur

U2 - 10.1016/j.tsf.2004.11.200

DO - 10.1016/j.tsf.2004.11.200

M3 - Article

AN - SCOPUS:21044458726

SN - 0040-6090

VL - 480-481

SP - 526

EP - 531

JO - Thin Solid Films

JF - Thin Solid Films

ER -

Cu(In,Ga)(S,Se)2 solar cells and modules by electrodeposition

Résumé

Accès au document

Empreinte digitale

Contient cette citation

Cu(In,Ga)(S,Se)₂ solar cells and modules by electrodeposition